
Heat Tape & Heat Cable Installation in Bailey, CO
At nearly 8,000 feet, a frozen pipe or a roof edge full of ice is a when, not an if. We install the GFCI-protected circuits, controllers, and pipe heat cable that keep water moving in Bailey, Conifer, Evergreen, and across the 285 Corridor.
Who Installs Heat Tape Near Bailey, CO?
Tri Peaks Electric Service handles heat tape installation for pipes and well lines, and the circuits for roof and gutter heat cable, in Bailey, CO and throughout Park and Jefferson County. We're a licensed Colorado electrical contractor (EC0103502) based in Bailey, and David Martinez is the lead electrician on every job.
The electrical side is what matters most. The National Electrical Code requires ground-fault protection for fixed de-icing and pipe-heating equipment (NEC 426.28 and 427.22), because a damaged cable can leak current and start a fire. We make sure that protection is there, the circuit can carry the load, and the cable runs only when it's needed.
Last updated November 2026.
Frozen Pipe and Ice Dam Prevention for Mountain Homes
Pipes in crawlspaces and exterior walls
Supply lines in unheated crawlspaces, garages, and north-facing walls are the first to freeze when it drops below zero.
Well lines and pitless adapters
Where the water line comes up into the house or well house. Lose that and you lose water until it thaws.
Roof edges and valleys
Heat cable on the eaves keeps a channel open so meltwater drains instead of backing up as an ice dam. We wire the circuit and controls it runs on.
Gutters and downspouts
Cable in the gutter and downspout gives meltwater a path off the roof. It needs a ground-fault protected outdoor circuit, which is our part.
Exposed drain lines
Drain line running through a crawlspace or under a deck can freeze too, and can be protected with heat cable on its own circuit.
Old heat tape that keeps tripping
We test the cable and the circuit, find the fault, and replace what's failed instead of bypassing the protection.
Self-Regulating Heat Cable vs. Constant-Wattage Heat Tape
Both keep pipes and gutters from freezing. They behave differently, and that changes what it costs to run them all winter.
| Feature | Constant-wattage tape | Self-regulating cable |
|---|---|---|
| How it heats | Same heat along its whole length | Output rises as it gets colder, drops as it warms |
| Controls | Usually needs a thermostat | Works alone; a controller saves more energy |
| Length | Often sold in fixed lengths | Cut to length on site |
| Best fit | Short, simple pipe runs | Roofs, gutters, long or complex runs |
How We Install a Heat Tape Circuit
- 1
Look at the problem spots
We look at the pipe runs, well line, crawlspace, or roof edge where freezing or ice dams happen, and check what power is already nearby.
- 2
Check the circuit and panel
We confirm the circuit can carry the cable's load and that ground-fault protection is in place or can be added at the breaker or outlet.
- 3
Install the circuit and controls
We add a GFCI-protected outlet or a dedicated circuit, plus a thermostat or controller so the cable runs only when it's needed.
- 4
Connect and test
We connect the cable per the manufacturer's instructions and test the circuit and the ground-fault protection before we leave.
- 5
Permit and inspection
For new circuits and hardwired systems we pull the permit and schedule the inspection, so the work is documented when you sell the house.
Why Heat Tape Is an Electrical Job, Not Just a Roofing One
Heat cable is a heater that lives outdoors, in snow and meltwater, for months at a time. The cable itself is only half the system. The other half is the circuit feeding it, the ground-fault protection that shuts it off when the jacket fails, and the controls that decide when it runs.
Common heat tape hazards start there: tape plugged into an extension cord, an outdoor outlet with no GFCI, or a tripping GFCI replaced with a regular outlet. The Consumer Product Safety Commission has warned since at least 1989 that worn heat tape is a fire hazard, and recommends checking it as you winterize your home.
If a pipe has already frozen and burst near wiring, shut off power to that area and call us. That's an electrical emergency, not something to wait out.
Fall Heat Tape Checklist
- Unplug it, then look along the whole run for cracks, charring, or bare wire
- Check the plug and end cap for discoloration or moisture
- Press the GFCI test button. If it doesn't trip, replace the outlet
- No extension cords, and no tape wrapped over itself unless the label allows it
- Replace any tape without a UL, CSA, or similar listing
More Winter Electrical Work
Heat tape is one piece of keeping a mountain home running through winter. These are the others we get called for most.
- Generator Installation →Inlets and transfer switches so heat, heat tape, and the well pump keep running in an outage.
- Baseboard & Wall Heater Repair →Cold rooms, dead thermostats, and heaters that won't shut off.
- Electrical Repairs →Tripping GFCIs, dead outdoor outlets, and well pump circuit troubleshooting.
- Panel Upgrades →Room for new heat cable circuits, heat pumps, and EV chargers.
- Electrician in Conifer, CO →Heat tape, panels, and generator hookups for Conifer and Aspen Park homes.
- Electrician in Evergreen, CO →Winter-ready wiring for Evergreen homes, cabins, and ADUs.
Heat Tape Installation Questions
Ready to Get Started?
Call or book online today. We serve Bailey, Conifer, Evergreen, and the entire 285 Corridor. Fast response — licensed & insured.